The greater the angle, the less weight an eye bolt can hold. If the angle is less than 5 degrees, the weight capacity stays pretty much the same. However, at just 15 degrees, the weight capacity is reduced by 20%. For example, an eye bolt with a 1/4 inch shank can typically hold up to 600 pounds at a straight pull (no angle).

For angle loading, see page 200. S-279 UNC Shoulder Type Machinery Eye Bolts diagrams and charts below before using eye bolt assemblies.

Some of the most reviewed products in Eye Bolts are the Hardware Essentials 1/2-13 x 10 in. Forged Steel Hot-Dipped Galvanized Eye Bolt with Hex Nut in Plain Pattern (5-Pack) with 41 reviews and the Everbilt 3/8 in. x 4 in. Zinc-Plated Eye Bolt with Nut with 29 reviews.

Fatigue rated at 1-1/2 times the Working Load Limit at 20,000 cycles. ! Working Load Limits shown are for in-line pull. For angle loading, see page 180. ! Meets 

All bolts threaded UNC. • Forged Steel - Quenched & Tempered. • Working Load Limits shown are for in-line pull. For angle loading, see page 196. • Meets or exceeds all requirements of ASME B30.26 including identification, ductility, design factor, proof load and temperature requirements. Importantly, these bolts meet other critical

Forged Eye Bolt Capacity and Strength Chart to show rated load capacities, must always be applied to eye bolts in the plane of the eye, not at an angle.

NOTES: The included angle, between the legs of every two-leg sling connected to a load by a pair of eyebolts or eyenuts, should not exceed 90 degrees.

Metric bolts are referenced using "M" sizes, such as the M8 bolt size. The size of a metric bolt is specified using pitch, diameter, and length in millimeters. For example, in M8-1.0*20, the "M" means the Metric thread designation, the digit 8 refers to the Nominal diameter (in millimeters), 1.0 refers to the pitch, and 20 refers to the

eye bolt angle chart MP1000 AIR FILTER DONALDSON ECG11-2501 AIR CLE rock crusher liner Z295 KEY REPLACEMENT KEY hard rock crushing. SCREEN-ALL Screen Aggregate Equipment For Sale. Dec 15, · SCREEN-ALL CR176. Screen Aggregate Equipment. Price: USD ,913 USD ,913 + VAT = USD ,850 ( VAT applies to users in

bolts at horizontal angle greater than 45 degrees. The working load limits specified in the chart require that: - the lifting eye bolt is completely screwed 

Swivel Lifting Eye Bolt is available to rotate 360°against the heavy lift shaft. displacement to single eye bolt depending on the lift angle.

Grade 80 eye bolts and eye nuts are manufactured from high tensile alloy steel and individually magnaflux crack detected after heat treatment. All lifting eyes are proof tested to 2.5 times the working load limit. Always select the correct eye bolt based on its type and capacity for the lift you are conducting.

All bolts threaded UNC. • Forged Steel - Quenched & Tempered. • Working Load Limits shown are for in-line pull. For angle loading, see page 196. • Meets or exceeds all requirements of ASME B30.26 including identification, ductility, design factor, proof load and temperature requirements. Importantly, these bolts meet other critical

Eye Bolts are load rated and made from forged steel that has been quenched and tempered. Bishop Lifting offers Regular Eyebolts along with Shoulder Eye Bolts, and Shoulder Type Machinery Eye Bolts. All of our eye bolts meet or exceed the requirements of ASME B30.26 including identification, ductility, design factor, proof load, and temperature

case of multi-leg slings the specified angle or range of angles. (2) When using slings in choke hitch multiply the marked SWL by 0.8 to obtain the reduced maximum load the sling may lift ie reduce the safe working load by 20%. (3) With multi-leg slings, when using less than the full number of legs, reduce the maximum load in proportion to the

Use a spreader bar with regular (non-shoulder) eye bolts to keep the lift angle at 90° to the horizontal. Use eye bolts at a horizontal angle greater than 45°. Sling strength at 45° is 71% of vertical sling capacity. Eye bolt strength at 45° horizontal angle drops down to 30% of vertical lifting capacity. Use a swivel hoist ring for angled