Measure with a standard tape measure and this will be the belt length needed. Belts can stretch with use over time, remember to check the sizes of the. V Belts 

Rubber vee belt B C SPB SPC section pitch length sizes n variable speed belts manufacturers Technical Specification of classical narrow wedge drive v belts 

Normal Horse Power H.P. Speed of Faster Shaft i.e. Motor Speed RPM V-Belt Section Permissible Min. Belt Pulley Pitch Diameter mm inch Recommended Min Belt Pulley Pitch Diameter mm inch 720 and below 900 1200 1800 ‰ to 11/2

Industrial V-belts ( classical V-belts ) have been covered in IS 2494 ( Part 1 ) : 1993 ‘V-belts - Endless V-belts for industrial purposes - Specification for wedge belts is under preparation. : Part 1 General purpose ( second r&ion )‘. The specification For the purpose of deciding whether a particular requirement of this standard is

Substitutions can be made based on this chart for 4L or 5L FHP belt sizes to "A/B" Super Gripbelt® or "AX/BX" Gripnotch® belts.

BELT I.D. CHART. Single V-Belts. Predator® V-Belts. SPCP. Aramid tensile cords provide superior service on high impact, shock-loaded drives.

All V-belt pulleys are compliant with current legislation and are made of cast iron GG 20with protective phosphate. Running in normal standard, the pulleys are statically balanced and this is sufficient for peripheral speeds up to 25 m/s. For higher speeds is essential dynamic balancing can be provided on request.

This technical manual contains all important technical information and methods for the design and calculation of drives with Optibelt V-belts and.

FEATURES: • Enhanced power rating by 20% - 30% • Enhanced belt life • Minimal belt stretch ARAMID / KEVLAR CORD BELTS FEATURES: • High tensile strength • Low stretch • Enhanced life DOUBLE COG BELTS X'tra DS FEATURES: • High power transmission capacity • Better heat dissipation • Extremely flexible Sections: Z, A, B, SPZ, SPA, SPB, 3V, 5V

Open the catalog to page 1. Technical Manual V-Belt Drives This technical manual contains all i ­mportant technical information and m ­ ethods for the design and calculation of drives with OPTIBELT V-belts and V ­ -grooved pulleys for industrial ­applications. Our Application Technology experts offer you free support service regarding the

Classical V-belt pulleys Classical belt Pitch diameter range Groove angle Dimensions series .b 1b dtc e - mm ° mm 13/A-17/B 85 - 17034 15,55 15,88 19,05 4,45 12,70 Over 170 38 15,88 19,05 4,45 12,70 22/C178 - 203 34 22,33 19,81 25,40 5,08 17,48 203 - 305 36 22,53 19,81 25,40 5,08 17,48 Over 305 38 22,73 19,81 25,40 5,08 17,48

Manufacturing Range. Belt Length Factor. Length. Designation. Tw (mm). Th (mm). Min Inch/mm. Max Inch/mm. Lp tp la (mm). Li to Lp (mm).

The V-belt size charts and dimensions for each type are discussed below. Standard V-belt. The standard V-belts are commonly used in power transmission. Standard V-belts come in various

The banded V-belt’s raw edge construction, three-ply laminated fabric and EPDM design ensure superior gripping power while the bottom cog construction provides extreme flexibility and cooling. By combining two belts using the common backing process, Dayco banded V-belts greatly reduce the tendency for single belts, which when subjected to

Size. Belt. Size. Pitch. Length. In (mm). Pitch. Length Do not pry or roll V-belts into the pulley grooves, if done so, the belts get damaged internally 

Engineering V-Belt Sheave Groove Dimensions Belt Section Outside Diameter Range m +/-0.25° bg + .005 hg Min. a S +/-.015 Se 3V, 3VX Less than 3.50 36°.350 .340 0 .406